Buying Guide
Turcite B Replacement Price: What Drives the Cost of Slideway Liner
The price of a Turcite B replacement is shaped by more than the liner itself. Material grade, width, thickness, cut length, packing and the amount of machining needed for the repair all affect the final cost. This TEBAK guide separates those cost drivers so rebuilders can prepare a useful specification and compare quotations on the same basis.
Why one slideway liner quotation can differ from another
A slideway liner quotation is normally built from a technical specification rather than a single universal price. Two requests that both say "Turcite B replacement" may require different widths, thicknesses, lengths, colours, packaging and machining allowances. The first step is therefore to compare equivalent materials and quantities before comparing the numbers on the quotation.
The main cost drivers
| Cost driver | What changes the cost | What to state in an inquiry |
|---|---|---|
| Material | PTFE-based compound, bonding treatment and required grade | Material family and etched bonding side |
| Dimensions | Width, thickness, length and the amount of trim allowance | Finished dimensions and machining allowance |
| Quantity | One repair piece, several cut pieces or a full roll | Number of pieces or total linear metres |
| Preparation | Cut-to-length, edge trimming, marking and protective packing | Cut list, labels and handling requirements |
| Transport | Destination, package size, weight and delivery method | Delivery country and receiving address |
Material and bonding surface
The material cost reflects the PTFE-based slideway compound and the manufacturing controls used to produce a stable liner. TEBAK supplies the same material family in Blue slideway liner, Green slideway liner, Brown slideway liner and Brick Red slideway liner. Colour is mainly a workshop identifier; the technical specification should also confirm the smooth running face and the chemically etched side prepared for bonding.
A quotation that includes the matching TEBAK Two-Part Epoxy-Adhesive may look higher than a liner-only price, but it can be easier to compare when the adhesive system is part of the same repair. Confirm whether adhesive, protective film and packing are included or listed separately.
Dimensions, quantity and workshop waste
Width and thickness affect both the material used and the way the strip is cut from production stock. Length affects the amount of roll material and the packing format. A cut-to-length piece can reduce workshop cutting work, while a full roll may be more economical for several machines but leaves the rebuilder responsible for layout and waste. Use the slideway liner sizing guide to record the way footprint, finished thickness and total run before requesting a price.
- Separate finished part dimensions from the extra material needed for trimming or finish machining.
- List every piece when one rebuild contains different widths or lengths.
- Ask whether the quoted length is a net usable length or includes an allowance for cutting.
- Compare the total usable area, not only the price per metre.
Packing and transport are part of the delivered cost
Long PTFE liner must be protected from creasing, contamination and edge damage. Cut pieces may need flat packing, while rolls need protection against crushing and moisture during handling. Transport cost also depends on package dimensions and destination, so a material-only figure is not the same as the delivered cost. Give the supplier the delivery country and preferred receiving method when asking for a complete comparison.
How to request a comparable quotation
- State the material family, colour and whether the etched bonding side is required.
- Give width, finished thickness, total length and a piece-by-piece cut list.
- Explain whether the liner will be finish-machined after bonding and how much allowance is needed.
- Ask for liner, adhesive, packing and transport as separate lines where possible.
- Compare the complete delivered specification, then confirm the drawing or sample before production.
Where TEBAK fits the price discussion
TEBAK supports both single-machine rebuilds and repeat purchasing with standard slideway liner, cut-to-length pieces and related bonding materials. Our TEBAK quality and supply guide explains the material and service checks behind a quotation. Send the machine way dimensions, required quantity and destination so the technical specification can be matched before price is compared.
Frequently asked questions
Frequently asked questions
Is Turcite B replacement price based only on thickness?
No. Width, length, quantity, cut format, packing, transport and any related adhesive or preparation service can also change the delivered cost.
Is a full roll always cheaper than cut-to-length liner?
Not automatically. A roll may suit several jobs, while cut-to-length pieces can reduce workshop cutting and waste. Compare usable material and labour for the actual repair.
What should I send for an accurate TEBAK quotation?
Send the colour, width, finished thickness, total length or cut list, machining allowance, adhesive requirement and delivery country. A drawing or clear dimensioned photo helps resolve unusual profiles.